Table of Contents
- 1 Do Renault Clio injectors need coding?
- 2 Do diesel injectors need coding?
- 3 Do you have to recode injectors?
- 4 Are 1.5 DCI injectors coded?
- 5 Do Bosch diesel injectors need coding?
- 6 Where is the injector code located?
- 7 Why does my Renault Clio have no fuel pressure?
- 8 Are there any problems with the Renault fuel pump?
- 9 What to do if your fuel pump is not working?
Do Renault Clio injectors need coding?
ClioSport Club Member Delphi injectors do need programing in, it should start and run without but better when programed in.
Do diesel injectors need coding?
Certain common rail diesel fuel injectors require calibration during manufacture or overhaul on a specialised diesel injection test rig to produce a data code relating to the characteristics of each individual injector. This data code may be referred. new injectors to be coded to the engine control unit.
What happens if you dont code an injector?
Non start – In newer systems if you do not code in the injectors the vehicle will not start. Poor / lumpy running – as the injectors are not coded, the ECU will carry on fuelling as if the previous injector was still present, which can cause poor performance.
Do you have to recode injectors?
Coding is fundamentally the most important aspect of CR injector calibration because new and reconditioned injectors alike need to be re-aligned to deliver the correct quantity of fuel at the right time during the combustion stroke, to meet stringent emissions standards.
Are 1.5 DCI injectors coded?
Re: 1.5DCI injectors-are they coded.? Hi there, Yes they are coded to the ecu, as far as i know the codes on them are like calibration codes etc and the ecu needs to know them .
What is injector mapping?
A fuel map is the combination of everything an ECU knows about engine running conditions. The goal of a fuel map is to use this information to provide the right amount of fuel. It does this by controlling fuel injector pulse width. Pulse width (PW) is the amount of time an injector is open in milliseconds.
Do Bosch diesel injectors need coding?
BOSCH Common Rail Injectors – generally all require coding, although some older versions may not. In simple terms, if the IMA code is present, then the injector will need coding. The typical code length is 6-10 digits and is located on the injector connector head.
Where is the injector code located?
These are generally found on the injector solenoid, or in the case of some Delphi injectors, found on the parts sticker located on the injector body.
What is injector learning?
Injector Pilot Learning or Small Quantity Learning Following Injector Coding or in some cases during routine servicing, manufacturers may require the technician carry out a procedure to teach the ECU the ideal Pilot Injection for the engine. This is called ‘Pilot learning’ or Small quantity learning’
Why does my Renault Clio have no fuel pressure?
This engine uses a Siemens SID 305 control unit with a flow regulator to fuel pump inlet, and a pressure regulator at the pump outlet. If the inlet receives no signal from the control unit no fuel enters the pump, resulting in no pressure in the fuel rail.
Are there any problems with the Renault fuel pump?
Renault is widely known for manufacturing tough and reliable cars. However, with time and use, problems with Renault fuel pumps can occur. In such situations, the opinions and insights of the Experts can be of great help in finding the right solutions.
Where is the fuel pump on a Renault Megane?
The Renault fuel pump in the vehicle is located inside the fuel tank. It can be accessed from the inside of the car by opening the top of the fuel tank. This diagram will depict the exact location. What are the basic checks that need to be done to test fuel pump functioning on a 2005 Renault Megane?
What to do if your fuel pump is not working?
If there is no sound, check for loose, broken or corroded connections. Next, check that the relay switches in and out and the contacts are bright and clean. Also check the fuses. Finally, test the voltage at the pump to see if the supply is 12 volts.